ka01isr.ino

Go to the documentation of this file.

//260414
 
/* 
* ISR INTEGRATION
* pro: we do use the standard atatchInterrupt from Arduino , easy etc
*
* ISR PINS TO USE
 
UNO(328P):  https://jensd.dk/doc/arduino/pins/uno.png
 
pin 2  (INT0) 
pin 3  (INT1)
 
MEGA(2560) https://jensd.dk/doc/arduino/pins/mega.png
 pin 21 INT0  NB: I2C SCL pin as well
 pin 20 INT1  NB: I2C SDA pin as well
 pin 19 INT2
 pin 18 INT3
 pin  2 INT4
 pin  3 INT5
 
 Atmega32u4 based micro
 intr 0,1,2,3,   intr is special - it you used it beware
Arduino micro(32u4 based)
pin 18 INT0
pin 19 INT1
pin 20 INT2
pin 21 INT3
pin  1 INT6
 
 NB NB NB 
 Only krnl calls allowd in isr: ki_signal and ki_send
 When using Arduino install of interrupts( attachInterrupt) you are not allowed to call krnls scheduler.
 
 So in worst case the task started by a interrupt krnl call (ki_signal, ki_send) will be running withn1 msec (at next krnl timer tick)
 
 SO NO K_CHG_STAK();    PUSHREGS();     POPREGS();  RETI();
}
* 
*/
 
#include <krnl.h>
 
// stak size
#define STK 150
 
 
char stkTask1[STK], stkTask2[STK];
 
#define TASKPRIO 10
 
struct k_t
  *pTask1,
  *pTask2,
  *isrSyncSem, *timedSem;
 
 
volatile int isrCount = 0, localCpy = 0;
 
void myISR() {
    isrCount++;
    ki_signal(isrSyncSem);
}
 
void task1() {
     
     int cn=0;
 
    k_set_sem_timer(timedSem, 500);
    while (1) {
        k_wait(timedSem, 0);
        Serial.print("isr counter ");
        Serial.print(cn++);
        Serial.print(" ");
        Serial.println(localCpy);
    }
}
 
 
void task2() {
 
    while (1) {
        k_wait(isrSyncSem, 0); // wait on kick from ISR
        // to ensure atomic access to isrCOunt you might disable interrupt
 
        DI(); // disable interrupt  - takes approx 62.5 nanosec
        localCpy = isrCount;
        EI();  // enable interrupt  - takes approx 62.5 nanosec
    }
}
 
void setup() {
    Serial.begin(115200);
    delay(500);
 
    Serial.println("\n\njust bef init part");
 
 
    k_init(2, 2, 0);  // 2 task, 2 semaphores, 0 messaegQueues */
 
    pTask1 = k_crt_task(task1, 15, stkTask1, STK);
    pTask2 = k_crt_task(task2, 15, stkTask2, STK);
 
    isrSyncSem = k_crt_sem(0, 10);  // 1: start value, 10: max value (clipping)
    timedSem = k_crt_sem(0, 10);    // 1: start value, 10: max value (clipping)
 
    pinMode(2, INPUT_PULLUP);  // for isr
 
    attachInterrupt(digitalPinToInterrupt(2), myISR, FALLING);  // install ISR
 
    Serial.println("justr bef start");
 
    k_start(); /* start krnl timer speed 1 milliseconds*/
 
    Serial.println("If you see this then krnl didnt start :-( ");
}
 
void loop() {}